Task Specific Adhesives & Repairers

Selleys Fibreglass Fix Repair Kit

Selleys_Fibreglass_Fix_100ml_S

Selleys Fibreglass Fix Repair Kit is a complete kit containing polyester resin, a hardener and fibreglass mat, for repairs to fibreglass and a variety of other surfaces.


Features

  • Non-corrosive
  • Weather resistant – resistant to water, weather or marine growth
  • Rapid setting
  • Impact resistant – can take knocks
  • Sandable – can be sanded after 1-2 hours
  • Can be painted over
  • Extended working time – up to 20 minutes at 20°C
  • Dries white
  • Heat resistant to 100°C

Available Sizes

  • 100mL Kit

Appearance

  • Dries white

Available at

  • Bunnings
  • Masters
  • Thrifty Link
  • Mitre 10
  • Home Hardware
  • Clark Rubber
  • Selected Paint Specialists
  • Selected Auto Retail Outlets

Where can this product be used?

  • Boat repairs including hull repairs
  • Surfboard / Surfski repairs
  • Automotive repairs
  • Repairing a leaky gutter
  • Patching downpipes
  • Patching metal roofs or grass catchers
  • Not approved for contact with drinking water

What materials is this product suitable for?

  • Fibreglass
  • Plywood
  • Metal
  • Fibro Sheeting
  • Most Plastics

How to use this product

  • Wear rubber or plastic gloves when handling fibreglass
  • Surface Preparation Surfaces should be clean and dry and free from paint, grease and rust. Cut the fibreglass mat to shape, allowing approximately 3cm overlap all round. Tease out the fibres along the edge of the mat to give a feathered edge.
  • For wide holes, glue a piece of cardboard to the back of the hole to form a base.
  • Mixing: For each tablespoon of resin, squeeze 5 drops of hardener from the small tube and mix together thoroughly.
  • Do not prepare the mixture until required as only a limited time (20 minutes at 20°C) is available before the product gels.
  • Application Position the mat and apply resin/hardener mixture with a clean, dry brush. Be sure to impregnate the mat completely, working out all air bubbles. Add more mat and resin/hardener mixture to build up or contour the patch as required.
  • Finishing When the patch has completely hardened, (approximatly 1-2 hours, depending on the temperature), it can be sanded to a smooth finish. Fill imperfections with more resin. Paint if required.
  • Clean up product with Solvent Acetone before it cures

Handy tips

  • At higher temperatures, the working time decreases.
  • Can only be tinted with iron oxide or other dry pigment .which must be mixed in very thoroughly.
  • Surfaces to be joined should be clean and dry.
  • If recommended amounts of hardener are not used, cure time will vary or an incomplete cure may result.
  • A useful solvent to clean up epoxy and polyester resins BEFORE they are cured can be prepared by mixing 2 parts toluene with 1 part alcohol (eg methylated spirits or denatured alcohol).
  • In large amounts heat can be generated during cure. Care should be taken on heat sensitive surfaces with large amounts.
  • Use recommended levels of hardener and resin; variation may result in incomplete cure and variations in cure time.
  • Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup.

Safety tips

  • Avoid contact with skin and eyes and avoid breathing resin vapour.
  • If poisoning occurs, contact a Doctor or Poisons Information Centre. Phone Australia 13 11 26 or New Zealand 0800 764 766.
  • If resin is swallowed, do NOT induce vomiting. Give a glass of water and seek medical advice.
  • If skin contact with resin or hardener occurs, remove contaminated clothing and wash skin thoroughly.
  • If irritation occurs seek medical advice.
  • If in eyes, hold eyelids open and flush with water for at least 10-15 minutes. Obtain medical attention.
  • For further information refer to the Material Safety Data Sheet (MSDS).

Storage and re-use

  • Store in cool place. Avoid contact with skin during handling.