Selleys Araldite Ultra Clear epoxy adhesive is a crystal clear adhesive which leaves an invisible bond line. It has excellent bond strength to a wide range of surfaces.

Features

  • Araldite is stronger than other glues due to the chemical reaction of the two parts
  • Bonds a variety of surfaces
  • Dries Crystal Clear so there's no visible evidence of repair
  • Quick setting in 5 minutes
  • Holds up to 130kg#
  • No clamping necessary
  • High water resistance
  • Forms a rigid, durable bond
  • Can be used for gap filling (Surfaces need not mate closely)
  • Good chemical resistance
  • Heat Resistant
  • Doesn't yellow over time so is ideal for use on glassware
  • Holds up to 130kg per cm2 when fully cured on steel

Where can this product be used?

  • Fixing a broken glass vase
  • Repairing jewellery
  • Toy repairs
  • Fixing ornaments or crockery
  • Fixing your handbag strap
  • Not suitable for bonding plastics such as Polypropylene and Polyethylene or for use on polystyrene

What materials is this product suitable for?

  • Glass
  • China
  • Metal
  • Wood
  • Rubber
  • Most plastics*
  • Crystal
  • Leather
  • *Will not bond Polyethylene or Polypropylene plastics.

Please contact your store to confirm avaliability, as some stores may have a limited range.

Size 8mL (2x4mL) Tube
  24mL syringe 
Colours Crystal Clear
Technology Epoxy
Use Interior 
  Exterior 

        To use Selleys Araldite Tubes:

  1. Clean and dry surfaces.
  2. Pierce each tube with spike found in top of its own cap
  3. Dispense equal parts of both liquids onto a clean disposable surface and mix both parts together thoroughly. The mixed glue will remain usable for 3-5 minutes at 20°C.
  4. Apply mixed glue to both surfaces of job – then bring together.
  5. Do not apply undue strain to bond for 30 minutes. Hold join in place using tapes or weights if necessary. Maximum strength reached after 16 hours.
  6. Place cap from plunger on nozzle for storage. Clean up uncured Araldite with acetone (nail polish remover).

        To use Selleys Araldite Syringe nozzles:

  1. Clean and dry surfaces.
  2. Snap out cap from plunger and carefully cut the sealed tips at the end of the syringe tip.
  3. Dispense equal parts of both liquids onto a clean disposable surface and mix both parts together thoroughly. The mixed glue will remain usable for 3-5 minutes at 20°C.
  4. Apply mixed glue to both surfaces of job – then bring together.
  5. Do not apply undue strain to bond for 30 minutes. Hold join in place using tapes or weights if necessary. Maximum strength reached after 16 hours.
  6. Place cap from plunger on nozzle for storage. Clean up uncured Araldite with acetone (nail polish remover).

        Limitations:

  • *Will not bond Polyethylene or Polypropylene plastics. 

 

 

  • For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time.
  • To extend product life replace caps immediately after use.
  • When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. Caps and tubes are colour coded to help.
  • To remove product after cure, mechanical action (scraping or sanding) is recommended.  Since the product is chemically resistant solvent will NOT dissolve this product.
  • Allow for longer bonding times in colder weather.
  • Bond strength will soften above 80°C but strength is retained when temperature returns to normal.
  • Protect from UV.
  • To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150°C. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment.  Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. 
  • Uncured product may be removed with acetone.
  • Cured product can be softened with heat to make scraping easier. 

Related Products

Selleys Araldite 90 Seconds

Selleys Araldite 90 Seconds epoxy adhesive is a 90 second setting, two part epoxy adhesive which enables a durable bond to a variety of surfaces without lengthy clamp times.

Selleys Araldite Super Strength

Selleys Araldite Super Strength epoxy adhesive is a super strong two part epoxy that has excellent adhesion to a broad range of surfaces and can hold up to 150kg*, making it ideal for sticking heavy loads.

Selleys Araldite Ultra Clear

Selleys Araldite Ultra Clear epoxy adhesive is a crystal clear adhesive which leaves an invisible bond line. It has excellent bond strength to a wide range of surfaces.


How to Guides